HP544+ 网卡测速
对 HP544+ 网卡进行速度测试
使用的软件主要是 iperf 和 iperf3，主要原因是某些情况下 iperf3 无法跑满带宽，因此需要补充 iperf 的测试。
软交换机器的测速
有一台技嘉 x99 ud4 机器，插了四块 HP544+ 网卡，都跑在 pcie 3.0 8x 上，cpu 是 e5 2680 v4 14核28线，物理机方式安装 debian 12 操作系统。使用系统默认的驱动。机器 IP 地址为 192.168.0.99 。
安装 iperf 和 iperf3 并设置 iperf3 自动启动。
$ uname -a
Linux switch99 6.1.0-18-amd64 #1 SMP PREEMPT_DYNAMIC Debian 6.1.76-1 (2024-02-01) x86_64 GNU/Linux
$ iperf --version
iperf version 2.1.8 (12 August 2022) pthreads
$ iperf3 --version
iperf 3.12 (cJSON 1.7.15)
Linux switch99 6.1.0-18-amd64 #1 SMP PREEMPT_DYNAMIC Debian 6.1.76-1 (2024-02-01) x86_64
Optional features available: CPU affinity setting, IPv6 flow label, SCTP, TCP congestion algorithm setting, sendfile / zerocopy, socket pacing, authentication, bind to device, support IPv4 don't fragment
本机测速
首先尝试 iperf3 访问本机的速度，即 iperf3 服务器端和 iperf3 客户端都在本地运行
$ iperf3 -c 192.168.0.99 -t 30 -i 1 -P 5
Connecting to host 192.168.0.99, port 5201
[ 5] local 192.168.0.99 port 43692 connected to 192.168.0.99 port 5201
[ 7] local 192.168.0.99 port 43702 connected to 192.168.0.99 port 5201
[ 9] local 192.168.0.99 port 43710 connected to 192.168.0.99 port 5201
[ 11] local 192.168.0.99 port 43712 connected to 192.168.0.99 port 5201
[ 13] local 192.168.0.99 port 43716 connected to 192.168.0.99 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 751 MBytes 6.29 Gbits/sec 0 639 KBytes
[ 7] 0.00-1.00 sec 751 MBytes 6.29 Gbits/sec 0 639 KBytes
[ 9] 0.00-1.00 sec 751 MBytes 6.29 Gbits/sec 0 639 KBytes
[ 11] 0.00-1.00 sec 751 MBytes 6.29 Gbits/sec 0 639 KBytes
[ 13] 0.00-1.00 sec 751 MBytes 6.29 Gbits/sec 0 639 KBytes
[SUM] 0.00-1.00 sec 3.67 GBytes 31.5 Gbits/sec 0
......
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec 0 sender
[ 5] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec receiver
[ 7] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec 0 sender
[ 7] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec receiver
[ 9] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec 0 sender
[ 9] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec receiver
[ 11] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec 0 sender
[ 11] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec receiver
[ 13] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec 0 sender
[ 13] 0.00-30.00 sec 22.8 GBytes 6.54 Gbits/sec receiver
[SUM] 0.00-30.00 sec 114 GBytes 32.7 Gbits/sec 0 sender
[SUM] 0.00-30.00 sec 114 GBytes 32.7 Gbits/sec receiver
测试出来的带宽只有 32.7 Gbits/sec ，非常的低。
改用 iperf ，启动服务器端
iperf -s -p 10001
开始客户端测试：
iperf -c 192.168.0.99 -t 30 -i 1 -P 10 -p 10001
测试出来的带宽是 286 Gbits/sec，远远大于 iperf3 测试出来的 32.7:
iperf -c 192.168.0.99 -t 10 -i 1 -P 10 -p 10001
------------------------------------------------------------
Client connecting to 192.168.0.99, TCP port 10001
TCP window size: 2.50 MByte (default)
------------------------------------------------------------
[ 2] local 192.168.0.99 port 54650 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/20)
[ 4] local 192.168.0.99 port 54656 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/24)
[ 1] local 192.168.0.99 port 54672 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/26)
[ 10] local 192.168.0.99 port 54716 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/17)
[ 3] local 192.168.0.99 port 54666 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/23)
[ 5] local 192.168.0.99 port 54680 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/24)
[ 6] local 192.168.0.99 port 54690 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/25)
[ 8] local 192.168.0.99 port 54724 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/24)
[ 7] local 192.168.0.99 port 54700 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/24)
[ 9] local 192.168.0.99 port 54730 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=319/32741/24)
[ ID] Interval Transfer Bandwidth
[ 5] 0.0000-1.0000 sec 3.36 GBytes 28.8 Gbits/sec
[ 7] 0.0000-1.0000 sec 3.33 GBytes 28.6 Gbits/sec
[ 4] 0.0000-1.0000 sec 3.26 GBytes 28.0 Gbits/sec
[ 2] 0.0000-1.0000 sec 3.33 GBytes 28.6 Gbits/sec
[ 3] 0.0000-1.0000 sec 3.23 GBytes 27.7 Gbits/sec
[ 9] 0.0000-1.0000 sec 3.25 GBytes 27.9 Gbits/sec
[ 1] 0.0000-1.0000 sec 3.24 GBytes 27.8 Gbits/sec
[ 8] 0.0000-1.0000 sec 3.35 GBytes 28.8 Gbits/sec
[ 6] 0.0000-1.0000 sec 3.28 GBytes 28.2 Gbits/sec
[ 10] 0.0000-1.0000 sec 3.22 GBytes 27.7 Gbits/sec
[SUM] 0.0000-1.0000 sec 32.8 GBytes 282 Gbits/sec
......
[ 5] 0.0000-10.0046 sec 33.9 GBytes 29.1 Gbits/sec
[ 4] 0.0000-10.0044 sec 33.0 GBytes 28.4 Gbits/sec
[ 2] 0.0000-10.0045 sec 33.0 GBytes 28.3 Gbits/sec
[ 9] 0.0000-10.0043 sec 33.3 GBytes 28.6 Gbits/sec
[ 8] 0.0000-10.0041 sec 33.1 GBytes 28.5 Gbits/sec
[ 10] 0.0000-10.0050 sec 34.1 GBytes 29.3 Gbits/sec
[ 3] 0.0000-10.0044 sec 33.0 GBytes 28.3 Gbits/sec
[ 6] 0.0000-10.0041 sec 33.1 GBytes 28.4 Gbits/sec
[ 1] 0.0000-10.0042 sec 33.3 GBytes 28.6 Gbits/sec
[ 7] 0.0000-10.0045 sec 33.5 GBytes 28.7 Gbits/sec
[SUM] 0.0000-10.0007 sec 333 GBytes 286 Gbits/sec
备注
注意并发线程即 -P 参数的影响很大，需要反复测试才能找到测试结果最好的参数。比如同样这台机器测试，-P 不同的结果是这样的：
-P 1: 33.1 Gbits/sec-P 2: 61.3 Gbits/sec-P 2: 147 Gbits/sec-P 8: 242 Gbits/sec-P 10: 288 Gbits/sec-P 12: 225 Gbits/sec-P 20: 163 Gbits/sec能看到 10 个测试线程可以跑到最高带宽 288 G，之后加大线程反而跑的更慢。
从其他机器访问
从其他机器访问，测试的这几台机器都是安装的 pve 8.1，linux 6.5 内核，同样是采用的操作系统自带的驱动。
物理网卡访问
在 pve 下直接访问软交换机器，此时可以视为两台物理机用网卡直连。
iperf -c 192.168.0.99 -P 10 -t 10 -i 1 -p 10001
测试结果为 47.6 Gbits/sec，根据经验，这是物理机模式下两块 hp544+ 直连能跑出来的最大带宽了。
iperf -c 192.168.0.99 -P 10 -t 10 -i 1 -p 10001
------------------------------------------------------------
Client connecting to 192.168.0.99, TCP port 10001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 4] local 192.168.0.19 port 54790 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/176)
[ 2] local 192.168.0.19 port 54788 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/149)
[ 1] local 192.168.0.19 port 54798 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/124)
[ 7] local 192.168.0.19 port 54806 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/113)
[ 5] local 192.168.0.19 port 54808 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/81)
[ 3] local 192.168.0.19 port 54800 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/106)
[ 10] local 192.168.0.19 port 54840 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/91)
[ 9] local 192.168.0.19 port 54830 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/49)
[ 6] local 192.168.0.19 port 54810 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/86)
[ 8] local 192.168.0.19 port 54824 connected with 192.168.0.99 port 10001 (icwnd/mss/irtt=14/1448/71)
[ ID] Interval Transfer Bandwidth
[ 10] 0.0000-1.0000 sec 805 MBytes 6.75 Gbits/sec
[ 4] 0.0000-1.0000 sec 189 MBytes 1.59 Gbits/sec
[ 9] 0.0000-1.0000 sec 804 MBytes 6.75 Gbits/sec
[ 1] 0.0000-1.0000 sec 194 MBytes 1.63 Gbits/sec
[ 8] 0.0000-1.0000 sec 798 MBytes 6.70 Gbits/sec
[ 6] 0.0000-1.0000 sec 362 MBytes 3.04 Gbits/sec
[ 7] 0.0000-1.0000 sec 448 MBytes 3.75 Gbits/sec
[ 5] 0.0000-1.0000 sec 808 MBytes 6.78 Gbits/sec
[ 3] 0.0000-1.0000 sec 445 MBytes 3.74 Gbits/sec
[ 2] 0.0000-1.0000 sec 815 MBytes 6.84 Gbits/sec
[SUM] 0.0000-1.0000 sec 5.54 GBytes 47.6 Gbits/sec
......
[ 10] 0.0000-10.0117 sec 7.91 GBytes 6.79 Gbits/sec
[ 9] 0.0000-10.0115 sec 7.92 GBytes 6.79 Gbits/sec
[ 1] 0.0000-10.0116 sec 2.00 GBytes 1.72 Gbits/sec
[ 6] 0.0000-10.0115 sec 3.84 GBytes 3.29 Gbits/sec
[ 5] 0.0000-10.0115 sec 7.81 GBytes 6.70 Gbits/sec
[ 2] 0.0000-10.0117 sec 7.93 GBytes 6.80 Gbits/sec
[ 8] 0.0000-10.0117 sec 7.87 GBytes 6.75 Gbits/sec
[ 3] 0.0000-10.0113 sec 3.97 GBytes 3.41 Gbits/sec
[ 7] 0.0000-10.0116 sec 4.01 GBytes 3.44 Gbits/sec
[ 4] 0.0000-10.0116 sec 2.08 GBytes 1.79 Gbits/sec
[SUM] 0.0000-10.0048 sec 55.3 GBytes 47.5 Gbits/sec
多台类似配置的机器，分别用同样的测试方法，得到的最高测试速度分别是：
- skyserver：47.5 Gbits/sec
- Skyserver2：43.6 Gbits/sec
- skyserver3：47.7 Gbits/sec
- Skyserver4：42.2 Gbits/sec
- Skyserver5：42.6 Gbits/sec
- Skyserver6：42.4 Gbits/sec
同样用 iperf3 测试:
iperf3 -c 192.168.0.99 -P 10 -t 10 -i 1
测试结果是 39.3 Gbits/sec :
iperf3 -c 192.168.0.99 -P 10 -t 10 -i 1
Connecting to host 192.168.0.99, port 5201
[ 5] local 192.168.0.19 port 40664 connected to 192.168.0.99 port 5201
[ 7] local 192.168.0.19 port 40672 connected to 192.168.0.99 port 5201
[ 9] local 192.168.0.19 port 40674 connected to 192.168.0.99 port 5201
[ 11] local 192.168.0.19 port 40678 connected to 192.168.0.99 port 5201
[ 13] local 192.168.0.19 port 40688 connected to 192.168.0.99 port 5201
[ 15] local 192.168.0.19 port 40700 connected to 192.168.0.99 port 5201
[ 17] local 192.168.0.19 port 40706 connected to 192.168.0.99 port 5201
[ 19] local 192.168.0.19 port 40716 connected to 192.168.0.99 port 5201
[ 21] local 192.168.0.19 port 40730 connected to 192.168.0.99 port 5201
[ 23] local 192.168.0.19 port 40734 connected to 192.168.0.99 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 432 MBytes 3.62 Gbits/sec 0 266 KBytes
[ 7] 0.00-1.00 sec 432 MBytes 3.62 Gbits/sec 0 267 KBytes
[ 9] 0.00-1.00 sec 432 MBytes 3.62 Gbits/sec 0 205 KBytes
[ 11] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 214 KBytes
[ 13] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 314 KBytes
[ 15] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 293 KBytes
[ 17] 0.00-1.00 sec 432 MBytes 3.62 Gbits/sec 0 233 KBytes
[ 19] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 187 KBytes
[ 21] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 310 KBytes
[ 23] 0.00-1.00 sec 431 MBytes 3.61 Gbits/sec 0 315 KBytes
[SUM] 0.00-1.00 sec 4.22 GBytes 36.1 Gbits/sec 0
......
[SUM] 0.00-10.00 sec 45.8 GBytes 39.3 Gbits/sec 0 sender
[SUM] 0.00-10.00 sec 45.8 GBytes 39.3 Gbits/sec receiver
还是比 iperf 速度慢不少。
sriov 虚拟网卡测试
vmbr 网卡测试
交换速度
其他两台机器通过软交换机相互访问的速度。
- skyserver：充当 iperf 服务器端
- Skyserver2：42.4 Gbits/sec
- skyserver3：36.2 Gbits/sec （和 skyserver 共用同一块网卡，受限于pcie3.0 8x 64g的总带宽）
- Skyserver4：42.3 Gbits/sec
- Skyserver5：42.2 Gbits/sec
- Skyserver6：42.2 Gbits/sec